[EU-Lieferung] WiFi BENZ C6 OEM DoiP Xentry Diagnosis VCI Multiplexer ohne HDD

Produktbeschreibung

WiFi BENZ C6 OEM DOIP Xentry Diagnosis VCI Multiplexer ohne HDD

Mercedes Benz C6 OEM Xentry diagnosis VCI DOIP Pasthru interfac is the latest interface for For Mercedes & SMART vehicles can replace Star C4/C5. XENTRY Diagnosis VCI acts as a Pass-through Interface, also called MB Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the XENTRY software loaded on a PC.
For full set, you can check SP332-Full

Mercedes Benz Xentry diagnosis VCI DOIP Pasthru interface Benz C6 Overview:

Compatible Software: VXDIAG For XENTRY/Das Software
Support Vehicle: Mercedes For Benz & Smart vehicles

DoIP: Support DoIP

Functions: Star Diagnostic & programming (SCN Coding)

What is DOIP?

DOIP is ISO 13400 diagnostic protocol

ISO 13400-1:2011 describes the general use cases and communication scenarios which are covered by an Internet Protocol-based vehicle communication standard. Each use case drives specific communication capabilities of the vehicle communication interface, for instance in order to be interoperable in an existing computer network.

The diagnostic communication over Internet Protocol (DoIP) protocol supports the standardized service primitive interface as specified in ISO 14229-2.

The descriptions in ISO 13400-1:2011 cover different application layer implementations, such as:

enhanced vehicle diagnostics (system diagnostics beyond legislated functionality, non-emissions-related system diagnostics);
WWH-OBD (World-Wide Harmonized On-Board Diagnostics) as specified in ISO 27145-2 and ISO 27145-3.

The mercedes  Land Rover JLR all use this new Diagnostic Protocol now.

Where do you need DOIP device?

when we test mercedes new car like w222  w205

In Audio\Comand section you can find DoIP test page.
If cable is DoIP you will see green mark that DEVICE is Ok.
Xentry will prompt you that other device must carry yellow marks.

Mercedes Benz Xentry diagnosis VCI DOIP Pasthru interface C6  Features:

1. TV Tuner
2. Keyless Go
3. Seat Electronics
4. Parktronic System
5. Instrument Cluster
6. Tyre Pressure Control
7. Drive Authorisation System
8. Assyst & ASSYST + systems
9. Headlamp Range Adjustment
10. Automatic Clutch System ACS
11. Electronic Ignition System (EIS)
12. Rvc, RST & Vario Roof modules
13. Sam (Signal Acquisition) Modules
14. Engines (All Gasoline & Diesel Systems)
15. Air Conditioning / climate control Systems
16. Transmissions and Electronic Selector Modules
17. Pneumatic System Equipment and ATA functions
18. Airmatic and Active Body Control Suspension Systems
19. Does not need a power supply unit for external power supply
20. D2b Command & Audio Gateway (D2B and MOST networks)
21. Can be used for all model series of For Mercedes For Benz vehicles
22. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
23. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
24. Support DoIP, cover more functions during SCN Coding than SD C4/C5
25. Diagnosis updates no longer necessary – firmware updates required on rare occasions
26. Dandy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
27. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM's
28. Functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on 

Mercedes Benz Xentry diagnosis VCI DOIP Pasthru interface C6 Summary:

Mercedes Benz Xentry diagnosis VCI DOIP Pasthru interface C6 (Vehicle Communication Interface) multiplexer serves as the interface to the vehicle when performing diagnosis and repairs, and programming electric and electronic on-board vehicle systems.
 
The Mercedes Benz Xentry diagnosis VCI DOIP Pasthru interface C6 does not have its own PC core, battery, fan, or display. It is operated using the VXDIAG For XENTRY Diagnosis Pad via WLAN or a USB cable connection.

Notice  :

1.Please install the 500GB HDD on laptop above 4GB Memory and I5 CPU, and use it on one laptop only. If change laptop, software may get broken and need to ship HDD back to us to copy software again.
2.ThisMercedes Benz Xentry diagnosis VCI DOIP Pasthru interface C6 can/'t support All Key Lost,needs one key at least.

BEZN C6 OEM(SP332) vs VCI C6 for Benz(SP332-B) vs BENZ C5(SP311) vs BENZ ECOM(SP335)

1. VCI C6 for Benz, with HDD, encrypted dongle, same housing with the original factory.
2. BENZ ECOM supports programming and diagnostic functions.
3. All of them only can work with the factory software.
4. All of them do not suport DTS Monaco & Vediamo
5.  All of them do not support old vehicles.

Paketliste:

1 set BENZ C6  Scanner ( If you need Software HDD, please check V2019.3 MB Star Software )

BENZ C6(SP332) vs Benz ECOM(SP335)

	Benz C6(SP332-Full)	Benz ECOM(SP335-SP100)
Firmware
Software	V2019.3	V2019.7
Old vehicles	some obd2 dianostic interface old vehicles, if it is not standard obd2 interface, it doesn't support.	Nein
Xentry Vehicles	Ja	Ja
DTS	Ja	Ja
Engineering software	Nein	Ja
DoIP	Ja	Ja
Online programming	Ja	Ja
HHT	Nein	Nein

 

Die Bearbeitungszeit beträgt 48 Stunden. Wenn es ein Wochenende ist, wird die kompatible Zeit verzögert.

Lieferzeit:

1. Pfosten, 10-17 Arbeitstage, keine Zoll meist. Für Deutschland und Großbritannien verwenden wir eine neue Postfirma, deren Zustellung nur 6-7 Werktage dauert.

2. YANWEN Express, 7-10 Werktag, ohne Zoll.

3. DHL: 5-7 Werktag, mit Zoll. Zoll hat die Pflicht des Kunden, aber wir schreiben als Standardwert mit niedrigem Wert, um Zollgebühren in Ihrem Land zu sparen. Wenn Sie Zollanforderungen benötigen, schreiben Sie uns bitte, wenn Sie die Bestellung aufgeben.

Finden unsere Web auf eurer Telefon:



Für Fragen, kontaktieren Sie uns bitte unter:

Telefon: +86-13559259264

Whatsapp: +86-13559259264

Email: sales@AutoOBD.de